Firmware

 

For Annikken Andee (Android), the latest firmware is Version 18.6

Click here to download Android Firmware 18.6

Click here to download Android Firmware 18.5

Click here to download Android Firmware 18.4

Click here to download Android Firmware 18.3

For Annikken Andee (iOS), the latest firmware is Version 2.51

Click here to download iOS Firmware V2.51

Click here to download iOS Firmware V2.5

Click here to download iOS Firmware V2.4

Click here to download iOS Firmware V2.3

For Annikken Andee U, the latest firmware is Version 1.58

Click here to download Andee U Firmware V1.58

Click here to download Andee U Firmware V1.56

Click here to download Andee U Firmware V1.55

Click here to download Andee U Firmware V1.54

Click here to download Andee U Firmware V1.5

For Arduino 101, the latest firmware is Version 1.21

Click here to download Arduino 101 Firmware V1.21

How to Check Andee Firmware Version

Step 1: Launch the Andee app on your smartphone and connect to the Annikken Andee.

Step 2: Press the Settings button at the top right hand corner of your screen.

Step 3: The settings window will open. At the top right hand corner of the settings window, you will find the firmware version of the connected Andee device.

Setting page.jpeg

How to Update the Andee's Firmware

Here's what you'll need:

  • 1x SD Card
  • 1x SD Card Reader/Writer (or a computer capable of reading/writing SD cards)
  • 1x Arduino
  • 1x Annikken Andee (Android or IOS)
Updating of Firmware

Step 1: Download the latest firmware from the link above.

Step 2: Extract the zip file and copy "image.hex" into an SD card.

Step 3: Connect the Annikken Andee to the Arduino and power it up. You should see an LED blinking. This means that the Andee is in Normal Mode.

Step 4: You'll need to put the Andee into Bootloading Mode. You'll need to do the following sequence:


Android

  • Press and hold down the button labelled, "BOOT" and "ANDEE RESET" Do not let go.
  • While holding BOOT down, release the RESET button.
  • Release "BOOT" button.

iOS

  • Press and hold down the button labelled, "BTN_0" and "BTN_1" Do not let go.
  • While holding BTN_1 down, release the BTN_0 button.
  • Release "BTN_1" button.


You'll now see the LED flashing red and flash green. These two LEDs will continue to flash alternately. Firmware updating is in progress. DO NOT DISCONNECT YOUR POWER SUPPLY.

Step 5: Insert SD card into the Annikken Andee's SD card slot

Step 6: When firmware updating is complete, the Andee will go back to Normal Mode. The alternate flashing will stop and will resume blinking green.

Click on the link to view video Annikken Andee Firmware Updating

Past Versions

If for some reason the latest firmwares gives you any problems, the following past firmware versions are available. We also appreciate that you email us a bug report regarding the problem you faced with any versions of firmwares:


Android Firmwares

  • Version 17

http://www.annikken.com/wp-content/uploads/2013/12/Firmware_v17.zip

  • Version 16_1

http://www.annikken.com/wp-content/uploads/2013/11/Firmware_v16_1.zip


iOS Firmwares

  • Version 1.2

http://www.annikken.com/wp-content/uploads/2014/09/Firmware-iOS-v1_2.zip

  • Version 1.0

http://www.annikken.com/wp-content/uploads/2014/09/Firmware-iOS-v1_0.zip

comments powered by Disqus